I would need help identifying the bullets, when they were used, who used them and what they are for. These are most likely rifle cartridges. The larger one would be a different caliber, would it be an aircraft caliber? I don't know.
dno nábojnice: nahoře Z, dole V a po bocích 1939
dno nábojnice: nahoře Z, dole V a po bocích 1939
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#382988
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
pokr.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#382992
Version : 0
Reklama
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Ten pěticentimotrový je možná ruský 7,62x54R, ale odoborník nejsem, takže to neber moc vážně
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383147
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
To těžko protože to číslo 54 udává délku samotné nábojnice.
Podle tvaru bych to spíš viděl na 5,45x39 mm.
Ten na obrázku s číslem 625, kde není udaný vůbec žádný rozměr, bych podle tvaru a indicie (jiný kalibr) viděl na 12,7x107 mm.
K přesnému určení je ovšem potřeba víc rozměrů (a celková dálka náboje to rozhodně není, protože ta se může lišit typem střely apod.):
průměr dna nábojnice průměr těla nábojnice nad drážkou průměr krčku nábojnice délka nábojnice průměr střely v místě usazení do krčku nábojnice
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383153
Version : 0
I'm sorry... as I said I'm not an expert
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383161
Version : 0
Reklama
I like that:
I'll measure it and post it here. What about the other bullets?
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383209
Version : 0
Yeah, the one with the number 625 is something like that, probably for an anti-aircraft gun, I'll measure and post.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383214
Version : 0
The three cartridges pictured in "length 7.7 cm.JPG" are 8x50 Mannlicher cartridges (see here forum.valka.cz )
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383215
Version : 0
It's bitax:
And the one on the right with the pointy bullet is also a manlicher?
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383216
Version : 0
Not knowing the caliber (bullet diameter) I'm boiling water, but the first three could be 7.92 Mauser based on the shape. The cartridge used for the Czechoslovak rifle vz. 24 (probably the first cartridge, the Z marking could mean Zbrojovka Brno, but I don't know much about the marking of cartridges, more how to shoot them ), the second two could be made by Hugo Schneider AG in Altenburg during WW2. They were used for both Mauser 98 rifles and machine guns.
For the group photo of the four cartridges, I'd guess from the shape that the first three are all the same (although I'm not sure if the third is longer or stands crooked) and is an 8mm Mannlicher. The fourth one could be an 8x56R M30 S.
For the 5cm one, my hypothesis about the 5.45x39 is supported by the fact that the 539 code is used by the Tula Ordnance Factory in the USSR.
And for the last one, again, the fact that I think I see remnants of black and red paint on the tip, which is the designation of the 12.7x107mm armor-piercing round.
But no dimensions (mainly caliber) with no warranty.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383217
Version : 0
Citace - bitaxe :
The three rounds in the "length 7.7 cm.JPG" image are 8x50 Mannlicher rounds (see here forum.valka.cz )
It could also theoretically be a 6.5mm Mannlicher, which looks virtually the same and is just narrower.
That's why you want to measure it.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383220
Version : 0
The basis of measurement is the diameter of the bullet, the photo is not how to determine how wide the bullet is, this is the first and most important data, then as Rad said just look at the Mannlicher in the link and measure it, then you can determine more. As for the Mannlicher cartridges, the first one was made before the war in 1910, the other two were made in 1917 and 1918 by Sellier and Belot. The Roman numerals at the top if I'm not mistaken indicate the quarter of manufacture. the mark at the bottom of the first hub is the manufacturer's designation. The fourth bullet is something else, it is made in an area where Cyrillic (or Cyrillic) was used which is the marking at the bottom (VF) personally I would guess Balkan, but off the top of my head I don't know and I'm too lazy to look anything up
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383221
Version : 0
Jasnačka, as soon as I have time, I'll measure it and post it here. Thanks for the preliminary info.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383230
Version : 0
I don't think you'll need to measure anything on the two steel ones. According to the bottom codes, these are clearly service German 7.92 x 57 cartridges for Mauser rifles. The first one has a painted steel cartridge with a reinforced bottom and a single-hole breech and was manufactured by "Hasag", Hugo Schneider A.G., Werk Altenburg im Thüringen in 1944 and fitted in production with the SmE bullet - pointed with iron core The second one also has a painted steel cartridge with a reinforced bottom and a single-hole breech and was also produced by "Hasag", Hugo Schneider A.G., Werk Altenburg im Thüringen in 1944 and fitted in production with a probably tin-plated (??) SmE projectile with iron core. The cartridge with this marking is missing in the precision tables of 7.92x57 cartridges so far ( the combination of numbers 44 41 ), so I have deduced the tin-plated bullet from the cartridges with codes 44 40 and 44 42. All of the above data can be read from the bottom markings. The Germans had a perfectly elaborate and therefore traceable marking system. I'll give you information on the other cartridges when I'm "declassified"
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383231
Version : 0
I'll be bouncing around like this, I don't think anyone wants to compete anyway The first one is probably also a 7,92x52 JS cartridge ( synonyms 7.92 mm German, CSR Vz.23 and j.) and was produced in Zbrojovka Brno, plant II Povážská Bystrica in 1939 in the fifth batch of that year. Therefore, it cannot be written well enough that it is a Czechoslovakian cartridge Vz.23.It was fitted with a 12.7 g projectile with a diameter of 8.22 mm, and had a power; Vo 780 m/s, Eo 3800 J. You should also measure the following dimensions :cartridge case length 57 mm, rim diameter 11.9 mm, base diameter 11.9,bullet diameter 8.22. The letters JS stand for "J" -Infantry and "S" stands for stark - reinforced ( as opposed to the original Mauser cartridge made before 1905) Just a little historical digression. After the establishment of the "Slovak State", the Tisova government was of course very interested in the Považsko-Bystrica armoury and ammunition. But Berlin "quickly tapped them on the fingers" and the Považský plant remained part of Zbrojovka Brno a.s.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383238
Version : 0
It's the sponsor:
Cool, thanks for the info, so I'll send the dimensions for the next ones and we'll see.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383242
Version : 0
Now, let's get down to the four brass The first three are 8x50 R Mannlicher cartridges The first one is marked with an Austrian double-headed eagle and was made in February 1910 The second was made by Sellier & Bellot in June 1917 the third also by S&B in January 1918 the fourth one is model 8x56 R Mannlicher and was made by the Bulgarian State Ammunition Factory - walking lion at 12 o'clock and - Letters (are in Cyrillic) Vf - voennaja fabrika in 1940 I attach a picture from the ND cartridge program
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383276
Version : 0
It's the sponsor:
12 o'clock? :-O
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383393
Version : 0
it means that it is in the position like 12 o'clock on the clock face, so at the top middle, at six it is of course at the bottom, at three on the right and at nine on the left it is quite common to mark the direction or position, it is used quite often just in the military in the landscape it is of course in the horizontal plane and 12 is in front of you
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383394
Version : 0
Yeah yeah, I know that's how the military determines it, pilots determine it too. It just didn't occur to me at the time. And I thought it was a lion, it didn't look like an eagle to me. Thanks.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383410
Version : 0
To give you an idea of the double-headed eagle, I've attached a picture of a similar bottom of a cartridge case. It's from J. Suchanek's book "Bullet Makers' Marks and Codes".
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383412
Version : 0
Ok, I recognize the two-headed Austrian-Hungarian eagle, but you wrote about the 8x56 R Mannlicher cartridge made in Bulgaria and that there is a walking eagle, I guess you meant to write lion, right?
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383415
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Dík, už je to opraveno. Je to samozřejmě bulharský lev.To víš, pracuj v noci Když tě mám na drátě, nemohl by jsi změřit ty zbývající nábojnice, alespoň obyčejným pravítkem. Nejdůležitější je délka nábojnice .Můžeš přidat i průměr dna - opět stačí pravítkem a odhadnout na půl mm.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383418
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Vzhledem k tomu že lev je ve státním znaku Bulharska jde zřejmě o něj a ta orlice je překlep
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383419
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
BTW, všiml jsi si, že náboj na snímku DSCN0625.JPG má dodatečně vloženou vystřelenou střelu ? Jsou na ní zřetelné stopy po vývrtu hlavně a také zahrdlení střely do ústí nábojnice žádné není. Navíc se mi vůbec nepozdává ta nová zápalka.Snad jsi jej nekupoval do sbírky
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383421
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
nene, nic jsem nekupoval, dal mě to už ani nevím kdo před mnoha lety a asi ten dotyčný to rozebral, vysypal prach, takže ty drážky na střele jsou asi od kleští, jak to rozdělával, čímž to znehodnotil.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383425
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Mám pro tebe i ostatní kolegy Valky zajímavou novinu. Jistě jsi si všiml toho odstavce v mém výkladu o nábojích 7.92x57 Mauser Pro připomenutí :..."Náboj s tímto značením zatím v precizních tabulkách nábojů 7.92x57 chybí( ta kombinace čísel 44 41 ), takže ten údaj o cínované střele jsem zatím vyvodil z nábojů s kody 44 40 a 44 42." Nedalo mě to, a obrátil jsem se ještě včera večer e-mailem na patrně největší kapacitu na značení těchto nábojů na světě, Holanďana Willhelm van Eijk. Text byla spíš šifra :
Betreff: 7,92x57 wg -St+ 44 41 (????) forum.valka.cz Quatí
a dnes koukám jak blázen -mám odpověď Vychutnejte si ji se mnou :
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383445
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
To zadavatel:
Ty s tím číselným uvedením 44 41 mám doma dva. Anglicky moc neumím, tak nevím, co ti pan Willhelm van Eijk napsal. Jdu poměřit ty ostatní nábojnice, co jsi nepopsal a napíšu to tu zachvilku.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383561
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Je to poděkování a že už tuto ražbu přidal do seznamu v uvedené stránce (to je ta dole). Stránka je zřejmě nejlepším a nejúplnějším zdrojem pokud se jedná o náboje 7,92x57, takže její doplnění je opravdu úspěchem.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383563
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Ještě si myslím, že označení toho čtvrtého náboje 8x56R Mannlicher není zcela přesné, aspoň podle Hýkela: forum.valka.cz
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383573
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Tak to jsem rád, že jsem přispěl aspoň troškou k takové důležité věci, která pomohla doplnit malý střípek do velkého celku.
Takže a teď k těm posledním dvěma nábojům. Ten o délce 5,6 cm má délku nábojnice 3.9 cm a průměr dna nábojnice 1 cm. Ten na fotce 0625 je délka nábojnice 10,8 cm a průměr dna nábojnice 2,1 cm.
Dál mám doma kousek kulometného pásu s náboji, délka nábojnice je 5,3 cm a průměr dna nábojnice je 1,4 cm, nábojnice kovová, soudím, že se jedná o náboje do kulometu UK 59, ráže 7,62.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383579
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Potom to odpovídá mým prvním odhadům (jsem se sebou spokojen, trefil jsem všechny ):
Poslední jsou skutečně podle rozměrů nábojnice náboje 7,62x54R - forum.valka.cz
A jen si trošku rýpnu v nejveselejší den v roce , jaká by měla být nábojnice, když ne kovová? Přece jen to není brokovnice, aby byla z papíru nebo plastu
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383583
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
tak to bude plechová, tmavě šedá.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383587
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
no ještě může být mosaz, ne? .-) A nebo že by i jiné kovové materiály? Jsem se asi špatně vyjádřil.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383588
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
a špičky střel v tom pásu jsou zlaté, zelené a stříbrné. I když na těch zlatých špičkách jsou vidět zbytky zelené barvy, takže asi je to jenom stříbrná a zelená.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383589
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Mosaz bejt může, akorát jsem si dycky myslel, že je to taky kov. Když si pročteš ten odkaz, tam máš značení špiček nábojů, co která znamená.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383590
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
a měděná nábojnice nemůže být? Mám doma jen nábojnici, která podle mě je ta samá jako v tom pásu co mám,7,62x54R, ale je jakoby měděná a uvnitř u vrchu potažená jemnou nazelenalou vrstvičkou, což je podle mě měděnka. Může být? A na dně je označení 17 a 77, nic víc.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383591
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
jj, už jsem to četl, ty barevné značení špiček.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383592
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Měď se příliš nepoužívala, je příliš měká, používány jsou slitiny s dalšími kovy tedy různé bronzy a mosazi. Ale každá slitina mědi se postupně při oxydaci může potáhnout měděnkou. Navíc většina starších nábojů se původně dělala s nábojnicí z barevných kovů a teprve později se nábojnice dělali železné (nebo ocelové) lakované. Důvodem byla jednak cena ale hlavně nedostatek barevných kovů například za války.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383593
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
tak jsem ten pás bliknul.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383594
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
tak tady je ta nábojnice.
že by to byla uvnitř měděnka? A nebo jenom povýstřelové spaliny?
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383600
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
To rad:
tak jsem poměřil "šuplerou" ten čtvrtý náboj 8x56R Mannlicher a stvořil jsem takový ne moc pěkný obrázek, tak ho tady zkontroluj.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383603
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
tak šťastný a veselý nový rok 2011 všem na valka.cz. ))
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383611
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Myslím že je jasné, že ta bulharská nábojnice byla určena správně, i když jsem její délku určoval interpolací v grafickém programu. Malá poznámka. Při určování nábojů se prakticky neuvádí celková délka náboje. Ta se může velice měnit. Takže jak jsem již psal je nejdůležitějším určovacím rozměrem délka nábojnice. Ještě k té mědi bych doplnil Bitaxe. Je ještě jedna možnost. Munice se také vyráběla z poměděného ( ev. naválcovaného) hlubokotažného plechu. Pokud je tvá nábojnice vyrobena z tohoto materiálu, stačí udělat vryp a měl by jsi to poznat.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383612
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Jo a ta nábojnice bude nejspíše z náboje 7.62x54 R Mosin-Nagant
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383616
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Ale jo, ten náboj je určen správně, akorát jak říkám, podle Hýkela se ten náboj takhle neznačí, synonym je sice halda, ale žádné není 8x56R Mannlicher. Výše máš odkaz, je tam kótovaný obrázek, můžeš si to porovnat sám, je to tentýž náboj.
Ty náboje jsou 7,62x54R, to už jsem psal, i ta prázdná nábojnice (uvnitř je podle zanešená zplodinami, to asi nebude měděnka. Ten kus pásu ale není z UK 59, aspoň já jsem takový pás v ruce neměl, u UK 59 se náboje nacvakávají víc dozadu a články nemají tvarování na dosedací kužel.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383628
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Jo, ( cit :"... akorát jak říkám, podle Hýkela se ten náboj takhle neznačí..") takhle už to beru. Ale až budeš mít chuť, dej ten název 8x56R Mannlicher do Goooglu a uvidíš jak je běžný. Užili jej i autoři vynikajícího programu "ND náboje" (pánové Neshyba a Daněk)a nechci znovu otevírat ostrou polemiku o tom, co a není synonymem názvu příslušného náboje, která zde již jednou byla. I mezi znalci jsou o tom spory a jako soudný člověk mám právo se přiklonit k názoru té či oné strany, případně si udělat názor svůj.A pokud budeš mít skutečný zájem, přečti si u tohoto náboje vysvětlení vzniku náboje právě v Hýkelově monografii a možná uznáš, že ten mnou zvolený název zcela přesně vystihuje o jaký náboj jde. A o to přece běží, není-liž pravda
A ještě jedna věc(i když to tady již napsal Bitaxe) - jsem přesvědčen, že ta stopa v ústí nábojnice je měděnka. Vzhledem k ohraničení stopy, je jasné, že se jedná o oxidaci zbytkového otěru z měděného pláště střely. Pokud byla pak nábojnice ve vlhku,tato zbytková měď se projevila oxidací.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383654
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Tak to máš recht, google ho pod tímhle názvem skutečně zná. Rozhodně nehodlám vyvolávat spory, pouze jsem měl dojem, že když je ten náboj zde na valce pod jiným jménem, asi bychom měli zájemce navést na tento náboj a ne mu dávat označení pod kterým ho u nás nenajde.
S tou měděnkou máš pravdu na zvětšené fotce je to dobře vidět i ten zelený nádech, zplodiny jsou víc do šeda.
Prográmek vypadá pěkně, i když třeba zrovna obrázek toho náboje je zcela chybný - dosedací kužel nábojnice je na něm asi poloviční oproti skutečnosti, zatímco krček je zase delší než by měl být.
A zkus ještě určit místo a datum výroby těch ruských nábojů (i když u toho 5,45x39 to bude nejspíš Tula a rok 1977), na tohle já literaturu nemám.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383683
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Poslyš a nebylo by lepší a rozumnější, kdyby Tango to synonymum prostě doplnil ? Přece jenom není dobré stavět odbornost na valce pouze na jedné knize i když si jejich autorů, pánů Hýkela a Malimánka velice vážím. Navíc pan Jindřich Hýkel již několik let spolupracuje s autory programu "ND náboje" na stránkách http://ndinfoservis.sweb.cz/ jako expert a my se tady budeme přít ? Co se té nábojnice 7.62x54 R Mosin-Nagant týká, tak kód "17" přísluší Barnaulské muničce (Barnaul (rusky Барнаул) je město v Rusku, na řece Ob v západní části Sibiře) a to číslo "77" bude s největší pravděpodobností vročení.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383700
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
No tak lepší a rozumnější to určitě je, koneckonců to můžeš s Tangem domluvit. Ale V TOM okamžiku tam ten název nebyl, tak mi přišlo rozumnější napsat ten, který tady v danou chvíli byl.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383703
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Jo a abych nezapomněl. Ten pás s náboji je myslím vidět zde
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383705
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Jak jsem se tak prohraboval v tom svém nevěstinci, našel jsem jednu zajímavou informaci. Ten bulharský náboj byl s velkou pravděpodobností vyroben na strojích dodaných v roce 1931 brněnskou Zbrojovkou do muniční továrny v Kazanliku a možná i z československého polotovaru - mosazných nábojových kalíšků, kterých v té době (1932) dodala Zbrojovka resp. bratislavská Munička 400 000 ks (40 vagonů)
Zdroj: FRANĚK Otakar "Zbraně pro celý svět - zahraniční obchod zbraněmi a municí koncernu Zbrojovka Brno mezi dvěma válkami" vydal Blok 1970 47-022-70 str. 90
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383717
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Citace - zadavatel :
Jo a abych nezapomněl. Ten pás s náboji je myslím vidět zde
Tak isto tento typ pásov bol používaný guľometmi radu PK : forum.valka.cz
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383723
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Označení nábojů v tom pásu je bxn a čísla asi 63 a 65 a nebo 53 a 55, nejde to moc dobře vidět.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383762
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
ale dík moc chlapi za určení, aspoň vím, co mám doma za poklady. )
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383763
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
bxn je označení výrobce, tedy Blanické strojírny Vlašim, čísla jsou posledním dvojčíslím roku výroby.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#383764
Version : 0
This post has not been translated to English yet. Please use the TRANSLATE button above to see machine translation of this post.
Jak budu mět víc času, dám sem i pistolové náboje co mám doma.
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#387865
Version : 0
I admit that now I am not entirely clear with whom the hub would be a synonym to be added?
The hub of the image DSCN0750.JPG are the 7,62x54R or 7,62 mm Mosin (with us 7,62 mm vz.59). Cartridge belt belonging to machine gun SG-43, which variant of the SGMT is used in the tanks T-54/55.
Ad copper - copper-plated cartridge cases ammo 7,62x54R and 7,62x39 is produced in the former USSR..
URL : https://www.valka.cz/Jake-jsou-to-naboje-t107641#388210
Version : 0
Join us
We believe that there are people with different interests and experiences who could contribute their knowledge and ideas. If you love military history and have experience in historical research, writing articles, editing text, moderating, creating images, graphics or videos, or simply have a desire to contribute to our unique system, you can join us and help us create content that will be interesting and beneficial to other readers.